BASIC TECHNOLOGY QUESTION BANK

REVIEW QUESTIONS If you are in JSS 2 and you are about to write your Third term examination, try the following questions and mail me your answer at basictechnologymadeeasy@gmail.com. Thank you. QUESTIONS 1.  A plane figure bounded by ten straight lines is called  (A) hexagon (B) heptagon  (C) octagon  (D) decagon. 2. A square that has its opposite sides equal and parallel but no angle is right is called….. (A) square  (B) rectangle  (C)  rhomboid  (D) rhombus. 3. An angle which is greater than 180 0  but lesser than 360 0 is called (A) acute angle (B) obtuse angle (C) reflex angle (D) a revolution. 4. The external angle of a regular polygon is 72 0 . Using the rule 360 0 /N determine the sides of the polygon. A. 6   B. 7   C. 5    D. 8 5. Which of the following is not a driving tool? A. drill  B. punch  C. hammer  D. mallet. 6. Which of the followi...

Welcome back. The following questions are set to test your ability to think, yes, rack your on topics and facts on what you really know. If you notice any difficult question, you are advised to consult your text book or notes. Now attempt the following questions and post your answers on our COMMENT option below. Again, if you have learnt anything from this exercises, please feel free to invite your friends from other schools to learn with us. Thank you.                                         Questions 1. When a metal can be drawn out or stretched in order to reduce the diameter to a fine wire, it is said to posses…………………………… 2. The five main parts of a tree are (i)…………..,  (ii)………………,  (iii)………………, (iv ………………….., and (v)………………. 3. Brass is an alloy consisting of the combination of ……………………+ …………………………. 4. The type of wood mostly found in tropical regions are……...

These are sample theory questions I asked my students during their first CA test. See if you can attempt some of these questions. Send me your answers at basictechnologymadeeasy@gmail.com                                             FIRST Assessment Test QUESTIONS-   INSTRUCTION: Attempt ALL questions. Each question carries FIVE marks. 1.List FIVE products of technology used at our homes. 2. State FIVE causes of accident in the workshop. 3. Write the full name of your Basic Technology teacher. 4. State FIVE things you have benefited from the application of technology in your school. 5. How would you define technology? 6. List FIVE areas where technology has improved our lives in Nigeria. 7. State FIVE reasons why you study technology. 8. List FIVE indigenous technologies in Nigeria and the state where they can be found. 9. How would you defin...

Now that we are done with drawing practice in class, why don't you attempt the following questions! You can post your answers on the COMMENT box below. Thank you. 1.Drawing paper should be stored in files or…………… a. scrolls or nylon jackets b. school bags c. left on the drawing board d. centre of notebooks 2. One of the following is NOT an information required in the title block. a. title b. time c. scale d. date 3. All measurements in technical drawing are stated in … a. micro meters b. multi meters c. millimeters d. centimeters 4.  The positioning of the title on a drawing is at the……….  corner. a. bottom left b. bottom right c. top left d. top right. 5. Which of these cannot be used to construct or draw a required angle? a. set-square b. protractor c. French curves d. ruler and compasses. Read More

Did you enjoy the session on scale drawing with your teacher? If yes, now attempt the following questions. You can send me your answers in the "COMMENT" box below. When you are done just click on 'Publish'. If you wish, you can equally mail me your answers at basictechnologymadeeasy@gmail.com. Thank you. QUESTIONS 1.One of the following is an enlarging scale. a. 5:6 b. 1:1 c. 2:1 d.1:5 2. Which of the following do you think represents reduced scale? a. 6:5 b. 1:10 c. 10:10 d. 100: 50 3. One of the following is a full scale. a. 30:60 b. 6:1 c. 100:100 d. 150:1500 4. Draw the line AB = 60cm to a scale of 1:10 a. 600mm b. 6mm c. 60mm d. 0.6mm 5. Calculate the length of a line EF = 70mm to a scale of 1:500. a. 14.0mm b. 1.40mm c. 0.41mm d. 0.14mm Read More

Now that you are through with this topic with your Basic Technology teacher, you can now attempt the following multiple choice questions. Feel free to post your answers including your name on our COMMENT tag below the questions. It will be marked and your result mailed to you via your email address. NOTE: Your email address will be treated with the utmost confidentiality.                                                         QUESTIONS 1. There are two types of Technology that we have learnt. They are: a. western/modern technology b. derived/African technology c. developed/under-developed technology d. none of the above 2. The use of one of the following is related to a high-developed technology. a.  knife and hoes b.  hooks and nets c.  horse drawn carts d.  air-crafts and cars. 3. Only one of the foll...

1. The Binis and Igbos are known for what indigenous technology? a. clothe weaving b. leather work c. sculpture work d. tie and dye 2. Technology is basically a subject for… a. girls only b. boys only c. anybody d. adults. 3. Technology should be studied for the following reasons EXCEPT… a. pleasure and recreation b. empowerment c. money making d. safety reasons 4. The Yoruba’s are known for one of the following indigenous technology. a. clothe weaving, tie and dye b. sculpture making c. leather work d. brass ornaments. 5. Leather work and Brass Ornaments are indigenous technologies related to….people of Nigeria. a. Southern b. Northern c. Western d. Eastern. Learn More